Wingate Anaerobic Power Calculator

Enter your test work values to get Wingate power output.

How it is calculated

The tool does not read raw pedal data; you supply work in joules for three windows, plus body mass in kg. Peak power is Ppeak = Wbest 5 s ÷ 5. Mean power is Pmean = W30 s ÷ 30. Minimum power is Pmin = Wlowest 5 s ÷ 5. Relative values divide the watts by body mass to give W/kg. The fatigue index is (Ppeak − Pmin) ÷ Ppeak × 100, the percentage of peak power lost by the weakest window. Mass must be above zero. The best 5-second work must be above zero and the lowest cannot be above it, and the 30-second total must lie between six times the lowest and six times the best 5-second work, since the 30-second mean is the mean of six 5-second windows; otherwise no result is shown, so a swapped pair gives no result instead of a negative fatigue index. These are the Wingate indices as Driss and Vandewalle (2013) describe them: peak power over the best 5 seconds, mean power over the 30 seconds and the drop from peak to the lowest power, given here as a percentage of peak, the form Bayrakdaroğlu et al. (2022) use. Body mass must be between 20 and 650 kg (the range of the Wingate anaerobic power page); outside it there is no result.

Worked example

A 75 kg rider records 4,500 J in the best 5 s, 3,000 J in the lowest 5 s, and 21,000 J over the full 30 s. Peak power = 4,500 ÷ 5 = 900.00 W. Mean power = 21,000 ÷ 30 = 700.00 W. Minimum power = 3,000 ÷ 5 = 600 W. Relative peak = 900 ÷ 75 = 12.00 W/kg, and relative mean = 700 ÷ 75 = 9.33 W/kg. Fatigue index = (900 − 600) ÷ 900 × 100 = 33.33%, so the rider lost a third of peak output by the weakest window.

Try this example →

Common mistakes

  • Entering average watts instead of joules. The fields take work in joules for the 5-second or 30-second window; typing 900 W as the best-5-s value would divide by 5 again and give 180 W.
  • Swapping the best and lowest windows. The lowest window cannot hold more work than the best one, so the tool shows no result; peak must be the larger number.
  • Using total work from a longer or shorter test. The mean divides by exactly 30 seconds, so a 20-second or 60-second effort gives a wrong mean power.
  • Entering body mass in pounds. Relative power is per kilogram, and pounds would make W/kg about 2.2 times too low.
  • Comparing fatigue index across athletes without noting the formula. It uses the lowest 5-second window, not the final one, so another lab's version using the last 5 seconds will differ.

Sources

About this calculator

The Wingate test is a 30-second all-out cycling sprint against a fixed resistance load (typically set relative to body mass), from which this calculator derives three standard metrics: peak power (the highest power output, usually measured over the best 5-second window, reflecting anaerobic alactic capacity), mean power (the average across all 30 seconds, reflecting anaerobic glycolytic capacity), and the fatigue index = (peak power − lowest power) ÷ peak power × 100%, which shows how quickly output drops off.

Sports scientists and exercise physiologists use the Wingate test, which a 2013 review by Driss and Vandewalle calls the all-out cycling test most often used, to measure anaerobic power and capacity, and strength and conditioning coaches use the resulting numbers to track an athlete's sprint and power-endurance development over a training cycle, particularly for sports like cycling, sprinting, and team sports with repeated high-intensity efforts.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

Ergometer software often reports watts rather than joules. To feed this tool, multiply the average watts of a window by its length: 900 W held for 5 seconds is 4,500 J. For comparing tests over a season, keep the load setting, warm-up and software window the same, since the numbers shift with them. Which ergometer software do you read your results from, and does it give watts or joules?

Comments

  • Be the first to comment.

Popular calculators

All Calculators