Tire Pressure for Load Calculator

Enter the load per tire and the tire's max load and max pressure to get a recommended psi.

How it is calculated

The tool scales the tire's maximum pressure by how heavily the tire is loaded: ratio = load ÷ max load, then psi = ceil(ratio × max psi × 1.10). The 10 percent safety margin is built in and the result is always rounded up to a whole psi, but it is never allowed above the tire's own maximum pressure, so a tire loaded to 90 percent or more of its capacity simply shows the maximum. On US units the loads are in pounds and the maximum pressure in psi; with the unit system set to metric they are in kilograms and kPa, the units most sidewalls also print (350 kPa = 51 psi). On metric the maximum is converted exactly (psi = kPa ÷ 6.894757), rounded up to the whole psi in the same way, and shown back in kPa with bar beside it (1 bar = 100 kPa), so the same tire gets the same pressure in either system. Loads are per tire; the maximum pressure comes from the sidewall. The load is also shown as a percentage of capacity. All three values must be above zero, and a load above the tire's maximum gives no result. There is no lower limit, so a very light load gives a very low figure (18 percent of capacity shows 9 psi in the sample tire) that may be below what the vehicle maker requires. The scaling is a straight proportion, a simplification that does not replace the vehicle placard or the manufacturer's load-inflation tables.

Worked example

A tire is rated for 2,200 lb at 44 psi and will carry 1,800 lb. Load ratio: 1,800 ÷ 2,200 = 0.8182, displayed as 81.82%. Scaled pressure: 0.8182 × 44 = 36.0 psi. With the 10 percent margin: 36.0 × 1.10 = 39.6, rounded up to 40 psi. That is below the 44 psi maximum, as expected for a tire carrying about 82 percent of its rated load.

Try this example →

Common mistakes

  • Entering the total vehicle or axle weight instead of the load on one tire. The tool works per tire, so divide an axle load by the number of tires on it.
  • Typing kilograms or kPa while the unit system is on US units. 350 read as psi or a 615 kg load read as pounds gives a wrong pressure; switch the unit system to metric for kg and kPa.
  • Reading 44 psi at 90 or 100 percent load as a calculated figure. Above roughly 91 percent of capacity the margin would exceed the tire's limit, so the tool just shows the sidewall maximum, which you must never go over.
  • Entering a load slightly above the rating and expecting a number. A load higher than the max load gives no result at all, because the tire is overloaded.
  • Taking the max pressure from the door sticker. Use the maximum inflation pressure molded on the tire sidewall, and set pressures cold: a tire that has just been driven reads several psi higher.

Sources

Based on a common rule of thumb; no published standard was found.

About this calculator

Tire manufacturers publish a maximum load rating paired with a maximum inflation pressure on every sidewall, and load capacity rises with pressure between those limits — carry less than the max load, and you can safely run somewhat less than the max pressure. This calculator estimates the pressure needed for your actual per-tire load by scaling from the tire's rated load-at-max-pressure point, then adds a safety margin. It works in pounds and psi, or in kilograms and kPa (with bar alongside) when the unit system is set to metric.

Getting this right matters for towing, RVs, and commercial trucking, where the load per tire changes with cargo and passengers: underinflation for the load causes excess heat buildup and sidewall flexing that can lead to blowouts, while overinflation reduces the contact patch and ride comfort. Fleet managers and tire technicians use load-inflation tables from organizations like the Tire and Rim Association for the same purpose.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

The figure is based on load alone. The pressure on your vehicle's tire placard is set with handling and wear in mind as well, so if the calculated value comes out below the placard number, the placard is the safer reference. Set pressures cold and recheck after loading. Do you tow, haul or carry a camper, and what sidewall maximum load and pressure do your tires show?

Comments

  • Be the first to comment.

Popular calculators

All Calculators