Sulfur Application Calculator
Enter your current and target soil pH, soil texture, and area to find the sulfur needed.
Result
How it is calculated
The tool reads Ohio State University Extension's fact sheet AGF-507 (2016), Table 1: pounds of elemental sulfur per acre to lower the pH of the top 6 inches of soil from 7.0, 7.5, 8.0 or 8.5 to 6.5 or to 5.5, for sand, silt loam and clay (cation exchange capacities of 5, 10 and 20 meq/100 g, soils not calcareous). The table adds up: going to 5.5 always costs the amount to 6.5 plus 460 lb (sand), 930 lb (silt loam) or 1,850 lb (clay). So the tool treats it as a curve, G(pH), zero at 6.5, joins the table's points with straight lines and takes rate (lb/acre) = G(current) − G(target); this gives every value in the table except clay from 7.0 to 5.5, 2,570 against 2,580 lb. The rate per 1,000 sq ft is lb/acre ÷ 43.56 and the total rate × area ÷ 1,000. Choosing Metric under Units takes the area in m² and gives the rate in g/m² (lb/acre × 0.1121) and the total in kg. Both pH values must lie between 5.5 and 8.5, the range of the table, and the current pH must be higher than the target, otherwise there is no result; the area must be above zero. A texture the tool does not know falls back to silt loam. The table assumes no free lime, and it does not split the dose: large amounts are usually spread over several applications.
Worked example
A 2,000 sq ft bed on silt loam, soil pH 7.5, target 6.0. Ohio State's Table 1 gives 600 lb of sulfur per acre for 7.5 to 6.5 and 930 lb more for 6.5 to 5.5, so 6.5 to 6.0 is half of that, 465 lb. Rate: 600 + 465 = 1,065 lb per acre, and 1,065 ÷ 43.56 = 24.45 lb per 1,000 sq ft. Total: 24.45 × 2,000 ÷ 1,000 = 48.90 lb of elemental sulfur. The same bed on clay needs 1,200 + 925 = 2,125 lb per acre, 97.57 lb in total, while sand needs only 24.33 lb: texture changes the amount about fourfold.
Common mistakes
- Entering the area in square meters with Units set to US. The US calculation expects square feet, so 200 m² is about 2,153 sq ft; or choose Metric and enter 200.
- Reading the US result as kilograms. In US units the result is in pounds (lb); one pound is about 0.45 kg. Metric gives kilograms.
- Applying the whole amount at once because the tool shows a single total. Large drops are usually split into several applications over time.
- Picking the wrong texture. Choosing sand for a clay soil would apply only about a quarter of what the table gives.
- Using it on soil with free lime. The table assumes soil that is not calcareous; calcium carbonate has to be neutralized first, which takes tons of sulfur per acre.
- Entering a target pH that is higher than the current one. The tool lowers pH only and returns no result in that case.
Sources
- Soil Acidification: How to Lower Soil pH (AGF-507), Table 1: Rates of elemental sulfur required to decrease soil pH to a depth of 6 inches — Ohio State University Extension (R. Mullen, E. Lentz, M. Watson), November 2016
About this calculator
Garden soil that is too alkaline for acid-loving plants like blueberries, azaleas and rhododendrons can be acidified by working in elemental sulfur, which soil bacteria (mainly Thiobacillus species) slowly oxidize into sulfuric acid over weeks to months, gradually lowering pH rather than shocking the soil the way a fast-acting acidifier would. How much sulfur is needed depends heavily on soil texture: clay soils have far more buffering capacity (cation exchange capacity) than sandy soils, so the same pH drop takes noticeably more sulfur in clay than in sand.
This calculator combines your current and target pH, soil texture, and treatment area (in square feet, or square meters in metric) to estimate the pounds (or kilograms) of elemental sulfur required. The rates come from Ohio State University Extension's fact sheet AGF-507, Table 1, which gives pounds of sulfur per acre to treat the top 6 inches when lowering pH from 7.0, 7.5, 8.0 or 8.5 to 6.5 or 5.5, for sand, silt loam and clay; the tool interpolates between the table's pH values, so both pH values must lie between 5.5 and 8.5. From 7.5 to 6.5 that is 6.89, 13.77 and 27.55 lb per 1,000 sq ft (33.6, 67.3 and 134.5 g/m²): clay needs about four times as much as sand, and the amount is not proportional to the pH drop. The table assumes soil without free lime (calcium carbonate); a calcareous soil needs far more, which the fact sheet calls impractical on a field scale. Compare the result with a soil test or your local extension service's advice. Because the reaction is bacterially driven, applications are typically split and worked into the topsoil weeks before planting rather than applied all at once.
Was this helpful?
You can pick up to 3 reactions.
Comments
- Be the first to comment.
Popular calculators
Loan Calculator
Monthly payment, total interest and full amortization schedule.
Percentage Calculator
Percent change, percent of, and ratio calculations.
Discount Calculator
Calculate final price, savings, and discount amount.
BMI Calculator
Body mass index from height and weight (metric or imperial).
Age Calculator
Compute your exact age in years, months and days from a birth date.
Compound Interest Calculator
Calculate the final amount and interest earned with compounding.
All Calculators
- Loan Calculator
- Profit Calculator
- Discount Calculator
- BMI Calculator
- Percentage Calculator
- Ideal Weight Calculator
- Age Calculator
- Pregnancy Due Date Calculator
- Compound Interest Calculator
- BMR Calculator (Basal Metabolic Rate)
- Tip Calculator
- Fuel Cost Calculator
- Date Difference Calculator
- Sleep Cycle Calculator
- Daily Water Intake Calculator
- Simple Interest Calculator
- Heart Rate Zones Calculator
- Running Pace Calculator
- Pet Age Calculator
- Calories Burned Calculator
- Macro Calculator
- TDEE Calculator (Total Daily Energy Expenditure)
- Waist-to-Hip Ratio Calculator
- Honor Roll Calculator
- One Rep Max (1RM) Calculator
- Ovulation Calculator
- Electricity Cost Calculator
- Unit Price Calculator
- Savings Goal Calculator
- Break-Even Point Calculator
- Paint Calculator
- Course Grade Average Calculator
- Business Days Calculator
- Time Duration Calculator
- Fuel Economy Calculator
- Temperature Converter
- Tile Calculator
- Aspect Ratio Calculator
- Roman Numeral Converter
- Goal Weight Timeline Calculator
- Salary Converter (Hourly to Annual)
- Credit Card Validator (Luhn)
- Body Surface Area (BSA) Calculator
- Feels-Like Temperature Calculator
- Ohm's Law Calculator
- PPI (Pixel Density) Calculator
- Molar Mass Calculator
- Zodiac Sign Calculator (Western + Chinese)
- IBAN Validator
- Shoe Size Converter
- Country Info & Dialing Code Lookup
- Time Zone Difference (World Clock)
- CAGR (Compound Annual Growth Rate) Calculator
- Rule of 72 Calculator
- Blood Alcohol Content (BAC) Calculator
- Lean Body Mass (LBM) Calculator
- Pythagorean Theorem Calculator
- Speed Converter
- Download Time Calculator
- Date Calculator (Add/Subtract)
No calculators found
Note from the editors
From pH 7.5 to 6.5 on silt loam, 1000 sq ft needs 13.77 lb; the same drop on clay is 27.55 lb and on sand 6.89 lb, from Ohio State's table, which assumes soil without free lime. Free lime resists acidifying, and bacteria oxidize the sulfur slowly, so results arrive over months. Re-test pH after a season before adding more. Did a lab test give your starting pH, or a home kit?