Stone Veneer Calculator

Enter your wall dimensions, openings, corner length, and waste percentage.

How it is calculated

All measurements are in feet by default; setting Units to metric takes the length and height in meters, the openings in m² and the corners in linear meters, and gives the orders in m² and meters (the default 0.75 sq ft per linear foot becomes 0.2286 m² per linear meter). gross area = length × height and net area = gross - openings, where openings is the total area of doors and windows in square feet. Corner pieces are bought by the linear foot, and each linear foot of corner replaces some flat veneer, so the tool removes allowance × corner length from the flat quantity. The allowance is an input: Coronado Stone's installation guide puts it at about 3/4 sq ft per linear foot on average, less for smaller profiles and more for larger ones, so the default is 0.75 and the coverage printed for your product should replace it. Both orders are then increased by the waste allowance: flat = (net - allowance × corners) × (1 + waste/100) and corners = corner length × (1 + waste/100). Empty openings and corners count as 0, an empty waste field means 10%, and typing 0 means no waste. The flat figure never drops below zero. Length and height must be above zero, and openings, corners and waste cannot be negative, or there is no result.

Worked example

A wall is 24 ft long and 9 ft high, with 40 sq ft of doors and windows, 18 linear ft of outside corners and 10% waste. Step 1: gross area = 24 × 9 = 216 sq ft. Step 2: net area = 216 - 40 = 176 sq ft. Step 3: at the default 0.75 sq ft per linear foot, the corners cover 18 × 0.75 = 13.5 sq ft, leaving 162.5 sq ft of flat veneer. Step 4: with waste, 162.5 × 1.10 gives 178.75 sq ft to order. The corner pieces come to 18 × 1.10 = 19.80 linear ft.

Try this example →

Common mistakes

  • Entering meters or square meters while Units is set to US. Every field is then in feet or square feet, so convert first or switch Units to metric.
  • Entering window width instead of window area in the openings field. Openings are in square feet: a 3 ft by 4 ft window counts as 12.
  • Entering the number of corners instead of their length. The field wants total linear feet, so four 9-ft corners are 36.
  • Expecting the flat total to equal wall area minus openings. The tool also takes the corner coverage off, so the flat figure is lower than net area plus waste.
  • Setting waste to 0 for a pattern with many cuts. If you leave the field empty the tool applies 10%, but typing 0 removes any allowance.

Sources

About this calculator

Stone veneer is sold and installed in two distinct products with different units: flat panels priced and measured by square footage for wall faces, and corner pieces priced by linear foot for outside corners, since a true corner piece wraps two faces at once and can't be measured in square feet the same way. Total flat coverage is wall area minus door/window openings, and also minus the wall area the corner pieces cover, which Coronado Stone's installation guide puts at about 3/4 sq ft per linear foot on average (smaller profiles less, larger more), so the allowance is an input with 0.75 as the default. Total corner length is simply the sum of all outside corner heights — both then padded with a waste allowance (10% if you leave it empty; commonly 5-15%) to cover cuts, breakage, and pattern matching.

This calculator takes your wall dimensions, openings, total corner length, and waste percentage and returns the flat veneer area and the corner-piece length to order, in square feet and linear feet or, with the metric Units option, in m² and meters. Masons and general contractors use it to generate accurate material orders and quotes before a job, and DIY homeowners use it to avoid under-buying (which risks a mismatched dye-lot on a reorder) or over-buying an expensive material.

Was this helpful?

You can pick up to 3 reactions.

Comments

  • Be the first to comment.

Popular calculators

All Calculators