Solar System Size Calculator

Enter your monthly usage, peak sun hours, and derate to size your solar system.

How it is calculated

The array size is found by dividing the energy you need per day by what one kilowatt of panels produces per day. kW = monthly kWh / (30 × peak sun hours × derate). Peak sun hours are the hours per day of full-strength sunlight at your site, and the derate is the fraction of the rated output left after losses (0.8 means 20 percent lost). Left blank it is 0.825: NREL's PVWatts default of 14 percent system losses (0.86) times its 96 percent inverter efficiency, the conversion to a single derate that the PVWatts Version 5 manual gives; a value above 1 gives no result. PVWatts works out the heat losses of the panels separately from weather data and this tool does not, so on a hot site enter a lower factor. The month is taken as a flat 30 days. The tool then counts panels as ceil(kW × 1000 / 400), assuming 400 W panels and always rounding up, and shows the daily output kW × peak sun hours × derate in kWh per day. All three inputs must be above zero. Roof space, shading, tilt, seasonal variation and local grid rules are not considered.

Worked example

A home uses 900 kWh a month, with 4.5 peak sun hours a day and a derate of 0.8. Energy per kW per day: 30 × 4.5 × 0.8 = 108 kWh per month for each kW of panels. System size: 900 / 108 = 8.33 kW, shown as 8.33 kW. With 400 W panels that is 8,333 / 400 = 20.8, rounded up to 21 panels. Daily output is 8.33 × 4.5 × 0.8 = 30.00 kWh, which matches 900 divided by 30 days.

Try this example →

Common mistakes

  • Entering the annual kWh or the daily kWh in the monthly field. The field is for a monthly figure, so use a typical month from your bill, or the yearly total divided by 12.
  • Using the sunshine hours from a weather report instead of peak sun hours. Peak sun hours are the equivalent hours at full intensity, normally much fewer than hours of daylight.
  • Entering the derate as a percentage such as 80. The field expects a fraction like 0.8, and a value above 1 gives no result.
  • Sizing to a single monthly average. Summer and winter output differ, so a system sized on the yearly average will produce a surplus in summer and a deficit in winter.
  • Treating the panel count as final. It assumes 400 W panels, so if your panels are 300 W or 550 W, divide the kW figure by your own panel rating.

Sources

About this calculator

Sizing a home solar array starts with how much electricity you actually use. The standard formula is System size (kW) = Monthly kWh usage ÷ (peak sun hours × 30 × derate factor), where peak sun hours measure the daily equivalent of full-intensity sunlight for your location and the derate factor, entered as a fraction, is the share of the panels' rated output left after losses: NREL's PVWatts takes 14% by default for soiling, shading, mismatch, wiring, connections, light-induced degradation, nameplate rating and availability, which leaves 0.86, and a 96% efficient inverter, so 0.86 × 0.96 ≈ 0.825 in all, the figure the tool uses when the field is left blank (PVWatts works out heat losses separately from weather data and this tool does not, so on a hot site enter a lower factor). The panel count shown assumes 400 W panels, rounded up.

Solar installers and homeowners use this calculation during the design phase to decide how many panels to quote, and utilities reference similar math when evaluating net-metering applications. Because peak sun hours vary by region and season, the same monthly usage can call for a noticeably larger system in a cloudier climate than in a sunny one.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

Panel count assumes 400 W modules and rounds up. If you have a different wattage in mind, divide the system size by it yourself: the default 7.27 kW needs 19 panels at 400 W but 17 at 450 W. Peak sun hours are not daylight hours, and a size based on your average month may undershoot in winter. What panel rating are you considering?

Comments

  • Be the first to comment.

Popular calculators

All Calculators