Rebar Spacing Calculator
Enter the span, target spacing, edge cover and bar diameter to count the rebars needed.
Result
How it is calculated
All lengths are in millimeters. Concrete cover is the distance from the concrete surface to the bar's own surface, not to its center: ACI's Concrete Terminology defines it as the "distance between the outermost surface of embedded reinforcement and the closest outer surface of the concrete", and TS 500 measures net cover from the outer face of the outermost bar. So the end bars' centers sit one cover plus half a bar diameter from each edge, and the bars are spread over centers = span − 2 × cover − diameter. The tool treats the spacing you enter as a maximum, so the number of gaps is rounded up: gaps = ceil(centers / spacing) and bars = gaps + 1. The bars are then spread evenly: actual spacing = centers / gaps, center to center, which is equal to or smaller than the target; the clear gap between neighboring bars is the actual spacing minus the diameter. There are always at least two bars, one at each end. Span and spacing must be above zero, cover cannot be negative and the diameter must be above zero; a link without a diameter uses 12 mm, the form default, and says so. A cover and diameter that leave no room between the end bars, or bars thick enough to touch at that spacing, give no result. The width inside the cover (span − 2 × cover) is shown as well. Check the result against the spacing and minimum-clearance limits of your design code.
Worked example
Span 3000 mm, target spacing 200 mm, cover 50 mm, 12 mm bars. The end bars' centers sit 50 + 12 ÷ 2 = 56 mm from each edge, so the bars are spread over 3000 − 2 × 50 − 12 = 2,888 mm. Gaps: 2,888 / 200 = 14.44, rounded up to 15. Bars: 15 + 1 = 16. Actual spacing: 2,888 / 15 = 192.53 mm, which is under the 200 mm limit, and the clear gap between neighboring bars is 192.53 − 12 = 180.53 mm. Had the span been 2912 mm, the 2,800 mm between the end bar centers would divide exactly into 14 gaps of 200 mm, so there would be 15 bars.
Common mistakes
- Rounding down the gap count and calling the result “about 15 bars”. Because spacing is a maximum, 14.44 gaps must become 15, giving 16 bars; fewer bars would break the spacing limit.
- Entering the span in meters or centimeters. All four fields are in millimeters, so 3 instead of 3000 makes the cover larger than the span and returns no result.
- Confusing the number of gaps with the number of bars. A row of 16 bars has only 15 gaps, which is the divisor in the actual spacing.
- Forgetting that cover is applied on both sides. The width inside the cover is the span minus twice the cover, not minus one cover.
- Entering the distance from the edge to the bar center as the cover. Cover is measured to the bar surface and the tool adds half the diameter itself, so 50 mm of cover with 12 mm bars puts the end bar centers 56 mm from the edge.
- Using the actual spacing as a rounded drawing dimension. 192.53 mm is the even distribution; detailers usually round it down to a practical figure such as 190 mm.
Sources
About this calculator
Reinforced concrete detailing needs an exact bar count and spacing for a given span: given the span length, the concrete cover required at each edge (measured to the bar surface), the bar diameter and a target center-to-center spacing, this calculator treats the spacing as a maximum, finds how many bars are needed so no gap exceeds it — n = ⌈(span − 2×cover − diameter) / spacing⌉ + 1 — and then recalculates the actual even spacing, which is therefore never wider than the target, so the bars land symmetrically rather than bunched at one side, which is how spacing is normally rounded on real drawings.
Structural engineers use this when preparing reinforcement schedules to satisfy code-required minimum and maximum bar spacing (per ACI 318 or equivalent), rebar detailers use it to produce accurate shop drawings, and concrete contractors use it on site to lay out and tie bars correctly before a pour.
Was this helpful?
You can pick up to 3 reactions.
Comments
- Be the first to comment.
Popular calculators
Loan Calculator
Monthly payment, total interest and full amortization schedule.
Percentage Calculator
Percent change, percent of, and ratio calculations.
Discount Calculator
Calculate final price, savings, and discount amount.
BMI Calculator
Body mass index from height and weight (metric or imperial).
Age Calculator
Compute your exact age in years, months and days from a birth date.
Compound Interest Calculator
Calculate the final amount and interest earned with compounding.
All Calculators
- Loan Calculator
- Profit Calculator
- Discount Calculator
- BMI Calculator
- Percentage Calculator
- Ideal Weight Calculator
- Age Calculator
- Pregnancy Due Date Calculator
- Compound Interest Calculator
- BMR Calculator (Basal Metabolic Rate)
- Tip Calculator
- Fuel Cost Calculator
- Date Difference Calculator
- Sleep Cycle Calculator
- Daily Water Intake Calculator
- Simple Interest Calculator
- Heart Rate Zones Calculator
- Running Pace Calculator
- Pet Age Calculator
- Calories Burned Calculator
- Macro Calculator
- TDEE Calculator (Total Daily Energy Expenditure)
- Waist-to-Hip Ratio Calculator
- Honor Roll Calculator
- One Rep Max (1RM) Calculator
- Ovulation Calculator
- Electricity Cost Calculator
- Unit Price Calculator
- Savings Goal Calculator
- Break-Even Point Calculator
- Paint Calculator
- Course Grade Average Calculator
- Business Days Calculator
- Time Duration Calculator
- Fuel Economy Calculator
- Temperature Converter
- Tile Calculator
- Aspect Ratio Calculator
- Roman Numeral Converter
- Goal Weight Timeline Calculator
- Salary Converter (Hourly to Annual)
- Credit Card Validator (Luhn)
- Body Surface Area (BSA) Calculator
- Feels-Like Temperature Calculator
- Ohm's Law Calculator
- PPI (Pixel Density) Calculator
- Molar Mass Calculator
- Zodiac Sign Calculator (Western + Chinese)
- IBAN Validator
- Shoe Size Converter
- Country Info & Dialing Code Lookup
- Time Zone Difference (World Clock)
- CAGR (Compound Annual Growth Rate) Calculator
- Rule of 72 Calculator
- Blood Alcohol Content (BAC) Calculator
- Lean Body Mass (LBM) Calculator
- Pythagorean Theorem Calculator
- Speed Converter
- Download Time Calculator
- Date Calculator (Add/Subtract)
No calculators found
Note from the editors
The actual spacing is measured center to center of the bars, so it is not the gap you can see. The clear gap line subtracts the bar diameter: with the defaults, 192.53 mm center to center and 12 mm bars leave 180.53 mm between neighboring bars. That is the figure to hold against minimum-clearance rules for placing concrete around the bars. Which code or maximum spacing are you detailing to?