Modified Shock Index Calculator

Enter heart rate and systolic and diastolic blood pressure.

Result

0.94
93.3 mmHg
0.7–1.3 (lower-mortality band, Liu 2012)

How it is calculated

The tool first finds the mean arterial pressure from the cuff reading: MAP = (SBP + 2 × DBP) / 3, in mmHg, where SBP is systolic and DBP is diastolic pressure. Then MSI = HR / MAP, with heart rate HR in beats per minute. MSI has no unit and is shown with two decimals. The category is taken from that rounded value: below 0.7 is labeled "Below 0.7", 0.7 to 1.3 inclusive "0.7–1.3 (lower-mortality band, Liu 2012)" and above 1.3 "Above 1.3". These are the cut-offs Liu et al. (2012) picked from one hospital's curve of MSI against mortality: values on either side of the band went with higher mortality. They are not a normal range. Heart rate and both pressures must each be between 1 and 400, and the diastolic must be below the systolic; otherwise no result appears. The label is a screening aid only; it ignores age, medication, pregnancy and the clinical picture, and it is not medical advice.

Worked example

A patient has a heart rate of 88 bpm and a blood pressure of 120/80 mmHg. The mean arterial pressure is (120 + 2 × 80) / 3 = 280 / 3 = 93.3 mmHg. The modified shock index is 88 / 93.33 = 0.94. That lies between 0.7 and 1.3, the band with the lower mortality in Liu et al. (2012), so the tool labels it "0.7–1.3 (lower-mortality band, Liu 2012)". For comparison, a heart rate of 130 with 90/50 gives a MAP of 63.3 mmHg and an MSI of 2.05, which is labeled "Above 1.3 (higher mortality in Liu 2012)".

Try this example →

Common mistakes

  • Entering the MAP in the diastolic box, or pulse pressure (systolic minus diastolic) as the diastolic value. The tool calculates MAP itself from SBP and DBP.
  • Swapping systolic and diastolic. If the diastolic value is not below the systolic one, the tool shows no result; check the order before reading anything into a missing result.
  • Confusing MSI with the classic shock index (HR divided by systolic pressure). The two use different denominators, so their values cannot be compared.
  • Reading the 0.7–1.3 band as normal or as reassurance. It is the band with the lower mortality in one retrospective study, it covers everything from 0.7 to 1.3, and a single reading says nothing about a trend; repeated measurements matter more.
  • Entering a heart rate from a pulse oximeter or a moving patient without checking it. A wrong HR changes the index in direct proportion.

Sources

About this calculator

The Modified Shock Index (MSI) is heart rate divided by mean arterial pressure (MAP), where MAP itself is calculated as diastolic pressure plus one-third of the pulse pressure (systolic minus diastolic). The tool shows the cut-offs of one study, Liu et al. (2012), a retrospective review of 22,161 emergency patients at one hospital in Beijing: the authors picked 0.7 and 1.3 from the curve of MSI against mortality, and patients above 1.3 (a hypodynamic state) and below 0.7 (a hyperdynamic state) both had higher mortality than those in between. The tool calls the middle band the lower-mortality band of that study; the study gives no normal range, and its authors ask for prospective confirmation.

In that study MSI predicted mortality better than heart rate or blood pressure alone, which is why it is studied as a triage aid in emergency medicine. This tool is for reference and education only, not medical advice.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

This index divides heart rate by mean arterial pressure, so it is not the same number as the older heart rate over systolic pressure index. Compare values with published cut-offs only if they use the same definition. One reading is a snapshot and cuff error moves it, so a clinician would look at the trend and the person, not the number alone. Do you usually work with this version or the systolic one?

Comments

  • Be the first to comment.

Popular calculators

All Calculators