Hot Tub Chemical Calculator

Enter your spa volume and chlorine levels to dose the sanitizer.

How it is calculated

The tool takes the spa volume, in US gallons or (with the unit system set to metric) liters, and the chlorine reading before and after in ppm:

increase = target − current (ppm)
dose (oz) = gallons × increase × 0.0001335 ÷ available-chlorine fraction
dose (g) = liters × increase ÷ 1000 ÷ available-chlorine fraction

The factor 0.0001335 is the weight in ounces of 1 ppm of chlorine in one US gallon; in metric, 1 ppm is 1 mg per liter, so liters × ppm gives milligrams. Because a product supplies only part of its weight as chlorine, the dose is divided by the product's fraction: dichlor 0.56, trichlor 0.90, calcium hypochlorite 0.65. A missing product is treated as dichlor, the usual hot tub choice, and the note says so; a product outside the list gives no result. A target above 5 ppm adds a warning that it is high. If the target is not above the current reading, or the volume is zero or negative, the tool shows no result. It only raises chlorine; it does not test or adjust pH, alkalinity or stabilizer.

Worked example

A 400-gallon spa reads 1 ppm and you want 4 ppm using granular dichlor. The increase is 4 − 1 = 3.00 ppm. Pure chlorine needed: 400 × 3 × 0.0001335 = 0.1602 oz. Dichlor supplies 56% chlorine, so 0.1602 ÷ 0.56 = 0.286 oz, which the tool shows as 0.29 oz. With trichlor (90%) the same change needs only 0.18 oz, and with calcium hypochlorite (65%) 0.25 oz.

Try this example →

Common mistakes

  • Typing liters while the unit system is on US units. A 1500-liter spa entered as 1500 gallons gets almost four times the dose; switch the unit system to metric instead, or enter about 396 gallons.
  • Typing the target as the amount to add. The target is the final reading, and the tool subtracts the current reading itself, so enter 4, not 3.
  • Entering a current reading of 0 when the test strip just was not read. A true reading changes the dose, since the tool only doses the gap.
  • Leaving the product on dichlor while actually adding trichlor or calcium hypochlorite. The dose differs for each (0.29, 0.18 and 0.25 oz in the example), so choose the product you really use.
  • Entering a target far above normal. Above 5 ppm the tool still gives a dose but warns that it is high for a hot tub; do not treat a larger number as safer.

Sources

About this calculator

Hot tub water needs a steady free chlorine (or bromine) residual, typically 3–5 ppm, to keep bacteria in check at spa temperatures, which are warm enough to let pathogens multiply quickly. Granular dichlor (sodium dichloro-s-triazinetrione) is the standard sanitizer for hot tubs rather than liquid or gas chlorine, because it dissolves fast, is nearly pH-neutral, and comes pre-stabilized with cyanuric acid to resist breakdown from heat and use.

This calculator estimates how much chlorine product you need — dichlor by default, or trichlor or cal-hypo, each adjusted for its available-chlorine content — to raise your spa from its current chlorine reading to your target ppm, based on your spa's water volume. Enter the volume in US gallons for a dose in ounces, or switch the unit system to metric for liters and grams. Getting the dose right avoids both under-sanitized water that risks bacterial growth and over-shocking that causes the sharp chlorine smell and skin irritation spa owners associate with bad water balance.

Was this helpful?

You can pick up to 3 reactions.

Comments

  • Be the first to comment.

Popular calculators

All Calculators