Glove Size Calculator

Enter your palm circumference in centimeters or inches to find your glove size.

Result

8.5
M
8.66 in

How it is calculated

You enter the circumference of your palm, measured around the widest part of the hand just below the knuckles with the thumb left out, in centimeters or, with the unit set to inches, in inches. The tool works in inches: inches = cm ÷ 2.54, then rounds to the nearest half size: size = round(inches × 2) ÷ 2. This follows EN ISO 21420, the European standard for protective gloves, whose sizes 6 to 11 sit at hand circumferences of 152, 178, 203, 229, 254 and 279 mm, one inch apart. The letter size comes from the numeric size: up to 4.5 is 3XS, up to 5.5 XXS, 6 to 6.5 XS, 7 to 7.5 S, 8 to 8.5 M, 9 to 9.5 L, 10 to 10.5 XL, 11 to 11.5 XXL, 12 to 12.5 3XL and above that 4XL. The value in inches is shown to two decimals as well. A hand below 12 cm or above 35 cm (sizes 4 to 13 cover 101 to 329 mm) gives no result. Brands do not all cut the same way, so check the maker's own size table, especially for work or safety gloves.

Worked example

A palm measures 22 cm around. Convert to inches: 22 ÷ 2.54 = 8.66 in. Double it: 8.66 × 2 = 17.32, which rounds to 17. Halve it again: 17 ÷ 2 = 8.5. A size of 8.5 sits on the upper edge of the M band (above 7.5, up to 8.5), so the letter size is M. The tool therefore reports size 8.5, letter M and 8.66 in. A palm of 22.3 cm would pass 8.5 and become size 9 and letter L.

Try this example →

Common mistakes

  • Measuring the length of the hand or the wrist instead of the palm circumference. The input is the distance around the palm, not the hand length.
  • Including the thumb in the measurement. The tape goes around the four fingers' base, with the thumb left out, which gives a smaller number.
  • Typing inches while the unit is on centimeters. 8.5 read as centimeters is far too small a hand and gives no result; switch the unit to inches, or type about 21.6 cm.
  • Pulling the tape too tight or leaving it loose. A tight tape underestimates and a loose one overestimates, which can move you by half a size or more.
  • Ignoring the brand chart. The tool uses the standard's steps; if your reading is near the boundary (such as 8.5 or 9.5), look at the maker's own sizes and the glove's material, since leather stretches and synthetic fabric does not.

Sources

About this calculator

Glove sizing is based on hand circumference — measured around the palm at its widest point, just below the knuckles, excluding the thumb. This calculator takes that measurement in centimeters or inches and converts it into a numeric glove size, the equivalent letter size from 3XS to 4XL used by most clothing and safety-equipment brands, and the value in inches. Under EN ISO 21420, the European standard for protective gloves, sizes step by about one inch of hand circumference (size 8 = 203 mm, size 9 = 229 mm), so the numeric size is the circumference in inches.

Accurate sizing matters for both fashion gloves, where a snug fit affects dexterity and appearance, and work and safety gloves (mechanic's, medical, or winter gloves), where a size that's too loose reduces grip and control while one that's too tight causes fatigue and restricts circulation during extended wear. Retailers and PPE buyers commonly reference size charts built on a circumference-to-letter-size mapping like this one.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

Brands do not agree on glove sizing, so this gives a starting point rather than a verdict. A 21 cm palm measures 8.27 in, which the tool turns into size 8.5 and letter M. Measure around the widest part of the palm with a soft tape, on the hand you use most, and between sizes pick by purpose: snug for cycling or golf, roomier for winter. Which kind of glove are you buying?

Comments

  • Be the first to comment.

Popular calculators

All Calculators