Fuel Pump Flow Calculator
Enter target horsepower, BSFC and fuel density to size the required fuel pump flow.
Result
How it is calculated
Mass flow is lb/hr = HP × BSFC, where HP is target engine horsepower and BSFC is in lb of fuel per horsepower-hour. It is converted to volume with L/h = lb/hr ÷ density, where density is in pounds per liter, and gal/h = L/h ÷ 3.785 (US gallons). With the unit system set to metric, BSFC is in grams per kilowatt-hour and density in kilograms per liter: kg/h = HP × 0.745699872 × g/kWh ÷ 1000 and L/h = kg/h ÷ density, the same flow as the US path for the same engine (horsepower stays in HP), and the mass flow is shown in kg/h. If you leave BSFC empty the tool uses 0.5 lb/hp·hr (about 304 g/kWh), and if you leave density empty it uses 1.62 lb/L (0.735 kg/L), which is about 6.1 lb per US gallon, a typical value for pump gasoline. Horsepower, BSFC and density must all be above zero. Results are rounded to one decimal for L/h and the mass flow and two decimals for gal/h. The figure is the engine's demand at the stated power, not a pump rating, so size the pump above it.
Worked example
Target 500 HP, BSFC 0.55 lb/HP·h, density 1.62 lb/L. Mass flow: 500 × 0.55 = 275.0 lb/hr. Volume flow: 275 ÷ 1.62 = 169.8 L/h (169.75 before rounding). In US gallons: 169.75 ÷ 3.785 = 44.85 gal/h. So the fuel system must deliver about 170 liters per hour at full power, and a pump with extra headroom above that figure is the sensible choice.
Common mistakes
- Entering density in lb per gallon (about 6.1), or in kg/L while the unit system is on US units. The US field is pounds per liter, so 6.1 would make the flow roughly four times too small and 0.74 more than twice too big; switch the unit system to metric for kg/L.
- Typing a BSFC in g/kWh (such as 300) while the unit system is on US units. It is then read as 300 lb/hp·hr, a flow 600 times too big.
- Using a naturally aspirated BSFC for a boosted or high-power build. A turbo engine often burns more fuel per horsepower, so 0.45 lb/hp·hr (274 g/kWh) can understate demand.
- Entering wheel horsepower where the formula expects engine (crank) horsepower; drivetrain loss makes the crank figure higher.
- Picking a pump whose rated flow equals the result. Pump ratings are quoted at a given pressure and drop under high pressure or low voltage, so a margin is needed.
Sources
- Specific Fuel Consumption (brake specific fuel consumption, fuel mass per hour per unit power) — NASA Glenn Research Center
About this calculator
Fuel pump sizing starts from how much fuel an engine actually burns to produce power, expressed as BSFC (brake-specific fuel consumption), typically in lb of fuel per horsepower-hour, or in grams per kilowatt-hour with the unit system set to metric. Required fuel flow is simply target horsepower multiplied by BSFC, giving a mass flow rate that the pump and injectors must be able to deliver.
Because pumps and fuel lines are usually rated in volume rather than mass, that mass flow is converted to a volumetric flow using the fuel's density (roughly 0.72–0.75 kg/L, or 6.0–6.3 lb/gal, for pump gasoline, higher for E85), producing figures in L/h and gal/h that tuners compare against a pump's rated flow at system pressure.
Engine builders and tuners use this to avoid fuel starvation under boost or high RPM — sizing the pump with margin above the calculated demand (commonly 20–30%) so injector duty cycle and pump output stay safely within limits at the target power level.
Was this helpful?
You can pick up to 3 reactions.
Comments
- Be the first to comment.
Popular calculators
Loan Calculator
Monthly payment, total interest and full amortization schedule.
Percentage Calculator
Percent change, percent of, and ratio calculations.
Discount Calculator
Calculate final price, savings, and discount amount.
BMI Calculator
Body mass index from height and weight (metric or imperial).
Age Calculator
Compute your exact age in years, months and days from a birth date.
Compound Interest Calculator
Calculate the final amount and interest earned with compounding.
All Calculators
- Loan Calculator
- Profit Calculator
- Discount Calculator
- BMI Calculator
- Percentage Calculator
- Ideal Weight Calculator
- Age Calculator
- Pregnancy Due Date Calculator
- Compound Interest Calculator
- BMR Calculator (Basal Metabolic Rate)
- Tip Calculator
- Fuel Cost Calculator
- Date Difference Calculator
- Sleep Cycle Calculator
- Daily Water Intake Calculator
- Simple Interest Calculator
- Heart Rate Zones Calculator
- Running Pace Calculator
- Pet Age Calculator
- Calories Burned Calculator
- Macro Calculator
- TDEE Calculator (Total Daily Energy Expenditure)
- Waist-to-Hip Ratio Calculator
- Honor Roll Calculator
- One Rep Max (1RM) Calculator
- Ovulation Calculator
- Electricity Cost Calculator
- Unit Price Calculator
- Savings Goal Calculator
- Break-Even Point Calculator
- Paint Calculator
- Course Grade Average Calculator
- Business Days Calculator
- Time Duration Calculator
- Fuel Economy Calculator
- Temperature Converter
- Tile Calculator
- Aspect Ratio Calculator
- Roman Numeral Converter
- Goal Weight Timeline Calculator
- Salary Converter (Hourly to Annual)
- Credit Card Validator (Luhn)
- Body Surface Area (BSA) Calculator
- Feels-Like Temperature Calculator
- Ohm's Law Calculator
- PPI (Pixel Density) Calculator
- Molar Mass Calculator
- Zodiac Sign Calculator (Western + Chinese)
- IBAN Validator
- Shoe Size Converter
- Country Info & Dialing Code Lookup
- Time Zone Difference (World Clock)
- CAGR (Compound Annual Growth Rate) Calculator
- Rule of 72 Calculator
- Blood Alcohol Content (BAC) Calculator
- Lean Body Mass (LBM) Calculator
- Pythagorean Theorem Calculator
- Speed Converter
- Download Time Calculator
- Date Calculator (Add/Subtract)
No calculators found
Note from the editors
The tool sizes flow to the horsepower you want to make, so choose a pump that exceeds it with margin, as pump ratings drop with voltage and pressure. At 500 hp, 0.5 BSFC and 1.62 lb/L it gives 250.0 lb/hr, 154.3 L/h and 40.77 gal/h. Boosted or ethanol-fed engines burn more fuel per horsepower, so raise BSFC. What power level and fuel are you building for?