Difference of Means Confidence Interval Calculator

Enter the mean, SD and size of each sample.

How it is calculated

The difference is d = mean₁ − mean₂. Its standard error combines the spread of both groups: SE = √(sd₁²/n₁ + sd₂²/n₂). The interval is d ± t × SE, where t is the two-sided Student t critical value for the chosen confidence with the Welch-Satterthwaite degrees of freedom df = SE⁴ ÷ [ (sd₁²/n₁)²/(n₁ − 1) + (sd₂²/n₂)²/(n₂ − 1) ]. The df is usually not a whole number and is not rounded; t is computed from the t distribution itself (for 10 df at 95 percent it is 2.228, as in printed t tables). The confidence field accepts only 90, 95 or 99 (blank means 95); any other value, such as 80, shows no result. Results are shown to four decimals, df to two and t to three.

This is the unpooled (Aspin-Welch) interval from OpenStax Introductory Statistics 10.1: it assumes two independent groups and takes each SD as a sample standard deviation. Each group needs at least 2 values, and at least one SD must be above zero. With large groups t approaches the normal 1.96 at 95 percent; with small groups it is much larger, so the interval is wider.

Worked example

Group 1 has mean 52.4, SD 8.1 and 40 observations; group 2 has mean 48.9, SD 9.3 and 45 observations. The difference is 52.4 − 48.9 = 3.5, shown as 3.5000. Standard error: √(8.1²/40 + 9.3²/45) = √(1.640 + 1.922) = 1.887. Welch degrees of freedom: 3.562² ÷ (1.640²/39 + 1.922²/44) = 82.97, so at 95 percent the critical t is 1.989. The margin is 1.989 × 1.887 = 3.754 and the interval is 3.5 ± 3.754, from −0.2540 to 7.2540. Because it includes 0, the data do not rule out no true difference at that level.

Try this example →

Common mistakes

  • Entering the standard error instead of the standard deviation. The SD describes spread among individuals; the tool computes the standard error itself, so using the SE would give an interval far too narrow.
  • Using it for paired data, such as before and after measurements on the same people. The formula assumes independent groups, so paired data need an interval on the within-pair differences.
  • Reading a 95 percent interval as a 95 percent chance that the true difference lies inside it for this particular study. It describes the long-run behavior of the method, not the probability for one result.
  • Typing a confidence level such as 80 or 97 and expecting a result. Only 90, 95 and 99 are recognized; anything else leaves the result empty.
  • Comparing with a z-based interval (1.96 × SE). With sample SDs the t value is larger, so the interval here is wider, by a lot for small groups.
  • Concluding that no difference exists because the interval contains 0. It means the data are compatible with no difference, but equally compatible with differences up to the upper limit.

Sources

About this calculator

When comparing two groups — a treatment vs. control group, two product variants, two time periods — the raw difference between their sample means only tells half the story. A confidence interval for the difference of means quantifies the uncertainty around that gap, built from each group's mean, standard deviation, and sample size using the standard error of the difference. Because the standard deviations are sample estimates, the tool uses Student's t with the Welch (Aspin-Welch) degrees of freedom, as in OpenStax Introductory Statistics: the variances are not pooled, so the two groups may have different spreads, and small samples get the wider interval they need.

This is a foundational technique in inferential statistics, used in A/B testing to decide whether an observed lift is likely real or just noise, in clinical trials to compare treatment effects, and in scientific research generally whenever two independent samples need to be compared rather than just eyeballed side by side.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

The width of the interval shrinks with the square root of the sample size, so to halve it you need about four times as many observations in each group. At the preset figures the interval runs from -2.30 to 12.30; raise both groups to 60 and 50 and it nearly excludes zero. The tool uses Student's t with Welch degrees of freedom, so small groups get a visibly wider interval than a z-based one. What kind of comparison are you making?

Comments

  • Be the first to comment.

Popular calculators

All Calculators