True Airspeed Calculator

Estimate true airspeed from IAS and altitude.

Result

139.20

How it is calculated

The tool applies the FAA's rule of thumb, add 2 percent to the calibrated airspeed for each 1,000 feet of altitude (Pilot's Handbook of Aeronautical Knowledge, chapter 8): TAS = CAS × (1 + 0.02 × altitude / 1000). CAS is the indicated airspeed corrected for installation and instrument error; the handbook notes that in the cruising range IAS and CAS are approximately the same, so the indicated reading serves as an approximation there. Altitude is in feet. The result has the same unit as the IAS you entered, so knots in gives knots out and the tool does no unit conversion. It shows two decimals.

The rule is linear and only uses altitude. It does not know about outside temperature, pressure setting, or instrument and position error, which are the things a flight computer would also use. The IAS must be above zero and the altitude cannot be negative; at 0 ft the answer equals the IAS. Treat the output as a planning estimate, not a figure for navigation that must be exact.

Worked example

An aircraft cruises at a calibrated airspeed of 120 knots at 8,000 ft (in cruise the indicated airspeed is about the same). The correction is 0.02 × 8,000 / 1,000 = 0.16, which is +16 percent. Multiply: 120 × (1 + 0.16) = 120 × 1.16 = 139.2. The tool shows 139.20, so the aircraft is actually moving through the air about 19 knots faster than its calibrated airspeed. At sea level the same 120 would stay 120.00.

Try this example →

Common mistakes

  • Entering the altitude in thousands of feet (8 instead of 8000). The formula divides by 1,000 itself, so the field needs the full figure in feet.
  • Entering the altitude in meters. The 2 percent rule is defined per 1,000 ft, so convert meters to feet first.
  • Treating the result as groundspeed. TAS is speed through the air; wind still has to be added or subtracted.
  • Trusting it for high or hot-day work. The rule ignores temperature and grows less accurate as altitude increases, so use a flight computer when it matters.
  • Entering the indicated airspeed at low speed or with flaps out. There installation and instrument errors can add up to several knots, so take CAS from the aircraft's airspeed calibration chart. Ground speed is never the input.

Sources

About this calculator

This calculator estimates true airspeed (TAS) with the FAA's rule of thumb: add 2% to the calibrated airspeed (CAS), the indicated airspeed corrected for installation and instrument error, for each 1,000 ft of altitude (Pilot's Handbook of Aeronautical Knowledge, chapter 8). In the cruising range IAS and CAS are about the same, so the indicated reading is a fair approximation there; at low speeds and with flaps the errors can reach several knots, and the airspeed calibration chart gives CAS. The correction is needed since air density drops with altitude and an airspeed indicator — which measures dynamic pressure, not true speed — reads increasingly low relative to the aircraft's actual speed through the air as it climbs.

Pilots use this quick approximation for flight planning and cross-country navigation when precise density-altitude data isn't at hand, since TAS (not IAS) is what determines groundspeed, fuel burn over distance, and time en route; for exact work they switch to a flight computer or E6B that also accounts for temperature deviation from standard.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

The answer is speed through the air, not speed over the ground. For a flight plan you still have to combine it with the wind to get groundspeed, which this tool does not do. A quick sanity check: at 10,000 ft the correction is plus 20 percent, so a calibrated 100 knots becomes 120 (in cruise the indicated reading is close to CAS). Tell us whether you enter altitude in feet or would want meters supported.

Comments

  • Be the first to comment.

Popular calculators

All Calculators