Tire Rolling Circumference Calculator

Enter the tire width, aspect ratio and rim diameter to get the rolling circumference and revolutions per km.

Result

1,932.9 mm
1,992.7 mm
634.3 mm
517/km

How it is calculated

Read a size such as 225/45R17 as width W in millimeters, aspect ratio A in percent and rim diameter R in inches. The sidewall height is s = W × A ÷ 100 mm. The overall diameter is D = R × 25.4 + 2s mm, because there is a sidewall above and below the rim. The static circumference is π × D. The tool multiplies it by 0.97, an assumed 3% loss from the tire flattening under load, to get the rolling circumference. Revolutions per km are 1,000,000 ÷ rolling circumference. Inputs must look like real markings: width 50–1000 mm, aspect ratio 10–100%, rim 4–60 in. Anything outside those ranges shows no result. The 3% factor is a fixed approximation, not a measurement of your tire. The 0.97 that turns the static into the rolling circumference is a typical estimate for a loaded tire, not from UN Regulation 30, which gives only the outer diameter; it is an input, so enter the maker's rolling circumference ratio if you have it.

Worked example

Tire 225/45R17. Sidewall: 225 × 45 ÷ 100 = 101.25 mm. Rim: 17 × 25.4 = 431.8 mm. Overall diameter: 431.8 + 2 × 101.25 = 634.3 mm. Static circumference: π × 634.3 ≈ 1,992.7 mm. Rolling circumference: 1,992.7 × 0.97 ≈ 1,932.9 mm. Revolutions per km: 1,000,000 ÷ 1,932.9 ≈ 517. For comparison, a 205/55R16 has a diameter of 631.9 mm, about 0.4% smaller, so a speedometer fitted for the first size would read about 0.4% high on the second.

Try this example →

Common mistakes

  • Entering the rim in millimeters or the width in inches. The width is in millimeters and the rim in inches, as printed on the tire wall; a rim of 431.8 is refused because it is outside 4–60.
  • Treating the aspect ratio as a height in millimeters. It is a percentage of the width, so 45 means a sidewall 45% as tall as the tire is wide; values below 10 or above 100 are refused.
  • Using the static circumference for speedometer or odometer comparisons. The rolling figure matches how far the car travels per turn, and it is about 3% smaller here.
  • Entering a width such as 22.5 for a 225 tire. Widths under 50 mm are rejected as an impossible tire.
  • Comparing only the width. Two tires with the same width but different aspect ratios or rims can have quite different circumferences.

Sources

About this calculator

A tire's rolling circumference is calculated from its size markings (for example 225/45R17): the sidewall height in millimeters equals the width multiplied by the aspect ratio percentage, doubled (for both sidewalls) and added to the rim diameter (converted from inches to millimeters), giving the overall tire diameter — that diameter multiplied by pi gives the static circumference, the rolling circumference is taken as 97% of it (allowing for about 3% tire deflection under load), and revolutions per kilometer is 1,000,000 divided by the rolling circumference in millimeters.

Drivers and mechanics need this number when comparing tire sizes for a plus-size or downsize wheel change, because a tire with a different rolling circumference than the factory-specified size throws off the car's speedometer reading, odometer accuracy, and — on cars with electronic stability control or ABS that rely on wheel-speed sensors — potentially the calibration of driver-assist systems; the standard rule of thumb is to keep the new tire's overall diameter within about 3% of the original to avoid these issues.

Was this helpful?

You can pick up to 3 reactions.

Comments

  • Be the first to comment.

Popular calculators

All Calculators