Nitrox MOD Calculator

Enter your oxygen percentage and maximum ppO₂ to find the safe maximum depth.

Result

33.8 m
111.4 ft

How it is calculated

The maximum operating depth is the depth at which the oxygen partial pressure reaches your chosen limit. The tool computes MOD (m) = (ppO₂ / FO₂ − 1) × 10, where ppO₂ is the limit in ata (roughly bar) and FO₂ is the oxygen share as a fraction, i.e. the percentage you type divided by 100. The factor 10 assumes that every 10 m of seawater adds one atmosphere on top of the 1 ata at the surface. The depth in feet uses the US dive-table rule of 33 feet of seawater per atmosphere, MOD (ft) = (ppO₂ / FO₂ − 1) × 33, so it is slightly more than the meter value times 3.28084. Both are shown to one decimal. The oxygen percentage must be between 21 (air) and 100, and the ppO₂ limit above 0 and at most 1.6 ata, the contingency maximum nitrox courses teach; values outside those ranges show no result. Type the percentage (32), not a fraction (0.32).

Worked example

For EAN32 (32% oxygen) with a working limit of 1.4 ata: FO₂ = 32 / 100 = 0.32. Then 1.4 / 0.32 = 4.375, and subtracting the 1 ata of surface air pressure leaves 3.375 ata of water pressure, which at 10 m per atmosphere is 33.75 m. The tool rounds this to 33.8 m. In feet it is 3.375 × 33 = 111.4 ft. A diver using this mix and this limit should stay shallower than that depth.

Try this example →

Common mistakes

  • Typing the oxygen fraction as 0.32 instead of 32. The field takes a percentage and accepts only 21 to 100, so 0.32 shows no result.
  • Entering the limit as a percentage or as a depth. The ppO₂ field is a pressure in ata, for example 1.4 or 1.6, and anything above 1.6 is rejected.
  • Rounding the result up. 33.75 m shown as 33.8 m is not a reason to plan a dive to 34 m; round down when you plan.
  • Using the result for a gas that is not plain nitrox. Only the oxygen share matters here, and nothing about helium, decompression or oxygen exposure time is included.
  • Choosing a limit that is too low for the mix. With 100% oxygen and a limit of 1.0 ata the depth is 0.0 m, meaning the limit is already reached at the surface.

Sources

  • Nitrox — Divers Alert Network (Alert Diver)

About this calculator

The maximum operating depth (MOD) of a nitrox blend is the deepest a diver can descend on that gas mix without the oxygen partial pressure (ppO₂) climbing past a chosen safety limit. It is calculated as MOD = ((ppO₂ limit ÷ FO₂) − 1) × 10, where FO₂ is the fraction of oxygen in the mix (you enter it as a percentage, e.g. 32 for EAN32, and the tool divides by 100) and depth comes out in meters of seawater using the 10 m-per-atmosphere rule, and in feet using the 33 ft-per-atmosphere rule of US dive tables.

Recreational nitrox courses from PADI, NAUI, and TDI teach divers to plan dives to a working ppO₂ limit of 1.4 ATA, with 1.6 ATA reserved as an absolute contingency maximum for the bottom portion of a dive — beyond that, oxygen toxicity risk (CNS oxtox) rises sharply. Because a richer mix like EAN36 lets a diver breathe more oxygen at any given depth than air, its MOD is shallower than air's; divers and dive planners use this calculator before every enriched-air dive to confirm the planned depth stays within the mix's safe limit.

Was this helpful?

You can pick up to 3 reactions.

Comments

  • Be the first to comment.

Popular calculators

All Calculators