Garden Watering Schedule Calculator

Pick your plant type and enter the area and recent rainfall to plan watering.

Result

137.1 gal/week
1.10 in
0.40 in

How it is calculated

Each plant type has a fixed weekly water target in inches: vegetables 1.5, the middle of the 1 to 2 inches Utah State University Extension gives for most vegetables; lawn, flowers and shrubs 1.0, N.C. State Extension's rule of thumb for most plants (a plant type outside the list gives no result). The tool subtracts the rain already received, never going below zero, then converts depth to volume: apply = max(0, need − rain) in inches, and gallons = apply × area × 0.623, with area in square feet and gallons being US gallons per week. Choosing Metric under Units takes the area in m² and the rainfall in mm: the targets become 38.1 mm for vegetables and 25.4 mm for the others, and since 1 mm of water over 1 m² is 1 liter, liters = apply (mm) × area (m²) per week. It also shows the inches still to apply and the rainfall credit. Area must be above zero, rainfall cannot be negative, and both fields must be filled in, with 0 entered for a dry week; otherwise there is no result. Real needs vary with soil, heat and wind, so treat the target as a starting point.

Worked example

A vegetable bed measures 200 sq ft and 0.4 in of rain fell this week. The vegetable target is 1.5 in. Still to apply: 1.5 − 0.4 = 1.10 in. Volume: 1.10 × 200 × 0.623 = 137.06 gallons. The tool shows 137.1 gal/week, with 1.10 in to apply and a 0.40 in rain credit. If the week's rain had reached 1.5 in or more, the result would be 0.0 gal/week.

Try this example →

Common mistakes

  • Entering the area in square meters or square yards with Units set to US. The US formula assumes square feet, so the volume comes out wrong by a factor of about 10.8 or 9; for square meters choose Metric.
  • Typing rainfall in millimeters with Units set to US: 10 mm of rain is about 0.39 in, not 10, and entering 10 wipes out the whole requirement. In Metric the field takes millimeters.
  • Leaving rainfall empty for a dry week. The field is required, so enter 0 to get a result.
  • Choosing lawn for a vegetable bed, or the reverse. The weekly target changes from 1.0 to 1.5 in, which changes the gallons by 50%.
  • Pouring the weekly total in one session when you water several times a week; the result is per week, so split it across your watering days.

Sources

About this calculator

Most garden plants need a fairly consistent amount of water per week to thrive — this calculator uses 1.5 inches per week for vegetable beds, the middle of Utah State University Extension's 1 to 2 inches for most vegetables, and 1 inch for lawns, flowers and shrubs, N.C. State Extension's rule of thumb for most plants. It subtracts the rainfall you enter for the week (in inches, or millimeters in metric) and converts what is left into actual gallons from your garden's area in square feet, or into liters from square meters.

The core conversion is gallons needed = inches of water × area (sq ft) × 0.623 — the constant comes from 1 inch of water over 1 square foot being 0.623 gallons. If your lawn needs 1 inch a week and you've already had 0.4 inches of rain, you only need to irrigate the remaining 0.6 inches' worth.

Home gardeners use this to avoid both underwatering (stressed, shallow-rooted plants) and overwatering (wasted water, root rot, runoff) by tailoring a watering schedule to actual weekly rainfall rather than watering on a fixed calendar regardless of recent weather.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

Treat the weekly water figure as a baseline. Area goes in square feet and rain in inches, and only rain that soaks in should be entered, since a light shower that wets the surface counts for little. Sandy soil drains fast and clay holds water, so spread the total over more or fewer sessions. Which plant type would you like added to the list?

Comments

  • Be the first to comment.

Popular calculators

All Calculators