Forced Carbonation Pressure Calculator

Set your regulator to hit a target CO2 level.

Result

11.25 PSI
Within 33–42 °F and 2.1–3.1 volumes, where the fit agrees with the Brewers Association table (sea level) to about 0.4 psi; 1 psi added per 2,000 ft of elevation.

How it is calculated

The tool uses a regression fitted to CO2 solubility data that homebrewers commonly use, with beer temperature T in degrees Fahrenheit and target carbonation V in volumes of CO2:

P = −16.6999 − 0.0101059·T + 0.00116512·T² + 0.173354·T·V + 4.24267·V − 0.0684226·V²

P is gauge pressure in PSI (above atmospheric). With the unit system on metric the temperature is typed in °C and the elevation in meters; the tool converts them to °F and feet (°F = °C × 9/5 + 32, feet = meters ÷ 0.3048) for the same fit and shows the pressure in bar (1 psi = 0.0689 bar), so the same keg gives the same setting in both systems. It is shown with two decimals. If the formula gives a negative number, the tool shows 0.00 PSI (0.00 bar). Volumes must be above zero. The fit is meant for beer at normal serving and cold-crash temperatures; the tool does not check the temperature range, so an out-of-range temperature still produces a number. Set the regulator to this pressure and give the keg time to reach equilibrium. The fit agrees with the Brewers Association's carbonation table (ASBC data, sea level) to about 0.4 psi between 33 and 42 °F (0.6 and 5.6 °C) and 2.1 and 3.1 volumes; outside that range it is an extrapolation and the result says so. At altitude the manual's rule of thumb is to add 1 psi to the regulator for every 2,000 feet (about 0.11 bar per 1,000 m), which the elevation box does.

Worked example

Beer at 38 °F in the keg, target 2.5 volumes of CO2.

Terms: −16.6999; −0.0101059 × 38 = −0.3840; 0.00116512 × 38² = 1.6824; 0.173354 × 38 × 2.5 = 16.4686; 4.24267 × 2.5 = 10.6067; −0.0684226 × 2.5² = −0.4276.

Sum ≈ 11.25, so set the regulator to 11.25 PSI.

At the same temperature a lower target of 2.2 volumes needs only about 8.09 PSI.

Try this example →

Common mistakes

  • Typing Celsius while the unit system is on US units. The field then reads Fahrenheit, so a 3.5 °C beer typed as 3.5 returns 0.00 PSI; switch the unit system to metric, or enter 38 °F.
  • Using the room temperature of the fridge door or the keg's surface instead of the liquid temperature. A few degrees warmer changes the pressure noticeably.
  • Confusing volumes of CO2 with percent or grams per liter. Typical beer targets are a few volumes, such as 2.2 to 2.8.
  • Reading the result as absolute pressure. It is gauge pressure, which matches the regulator dial.
  • Setting the pressure and expecting instant carbonation. The beer needs days at that pressure to reach equilibrium, and a long beer line or serving pressure may differ from the carbonation pressure.

Sources

About this calculator

Forced carbonation dissolves CO2 into beer under pressure rather than waiting for natural bottle conditioning, and the pressure needed to reach a target carbonation level (measured in volumes of CO2) depends heavily on the beer's temperature, because colder liquid holds more dissolved gas at a given pressure — the relationship is captured in CO2 solubility tables or the corresponding regression formula that homebrewers and commercial brewers both rely on.

Homebrewers with a kegging setup and CO2 tank use this to dial in a regulator to a precise pressure (psi, or bar with the unit system on metric) for a target style — British ales are typically carbonated to lower volumes than German lagers or Belgian styles, for instance — and getting the pressure-to-temperature match right avoids both flat beer and over-carbonated, gushing pours.

Was this helpful?

You can pick up to 3 reactions.

Comments

  • Be the first to comment.

Popular calculators

All Calculators