Cycling Calories From Power Calculator

Turn your average watts into calories burned.

Result

1,231
972 kJ
13.7
972

How it is calculated

The tool first converts your average power and ride time into mechanical work: work (kJ) = power (W) × duration (min) × 60 ÷ 1000. It then turns work into energy spent with the relation Haakonssen and colleagues measured in trained road cyclists (Medicine & Science in Sports & Exercise, 2013): energy (kJ) = work (kJ) × 5.3, a gross efficiency of about 19%, and divides by 4.184 kJ per kcal (NIST): kcal = kJ × 5.3 ÷ 4.184 ≈ kJ × 1.27. The common shortcut kcal = kJ, shown as a separate line, assumes about 24% efficiency and reads about a fifth lower. There is no efficiency setting. The third result is calories per minute, kcal ÷ minutes. Power and duration must both be above zero. Use average power for the whole ride, including easy parts, not your best effort.

Worked example

You ride 90 minutes at an average of 180 W. Seconds: 90 × 60 = 5,400 s. Work: 180 W × 5,400 s = 972,000 J, or 972 kJ. Energy spent: 972 × 5.3 = 5,151.6 kJ, and 5,151.6 ÷ 4.184 = 1,231 kcal, shown together with 972 kJ of work. Calories per minute: 1,231 ÷ 90 = 13.7. The common shortcut, one kcal per kJ of work, would say 972. A ride at the same average power for twice as long would burn twice as much, so doubling the time to 180 minutes gives 2,463 kcal.

Try this example →

Common mistakes

  • Entering the duration in hours. The box takes minutes, so a 1.5 hour ride must be typed as 90, otherwise the result is 60 times too low.
  • Using peak or normalized power in place of average power. Normalized power is higher than what you really did, so the calorie figure comes out too high.
  • Leaving out the stops. Time spent coasting or standing still at lights counts as zero watts in an honest average, so include it in the power or use the moving time for both.
  • Counting the whole figure as extra. Gross efficiency covers all the energy spent during the ride, resting metabolism included, so what riding adds over sitting still is a little less.
  • Treating the number as exact. The 19% efficiency is a group mean; the study found individual errors of about 11%, so your own figure can differ.

Sources

About this calculator

Estimating cycling calories from power output is more accurate than heart-rate or speed-based estimates because a power meter measures the actual mechanical work you produce, in watts, independent of fitness level, wind, drafting, or heart-rate drift over a long ride. The conversion rests on the body's gross efficiency, the share of the energy you burn that ends up as work on the pedals. Haakonssen and colleagues (Medicine & Science in Sports & Exercise, 2013) measured about 19% in trained road cyclists and give energy expenditure = work in kJ × 5.3; with 4.184 kJ to the kilocalorie, each kilojoule of work costs about 1.27 kcal, which is what this tool uses. The common shortcut that counts one kilocalorie per kilojoule of work assumes about 24% efficiency and reads about a fifth lower; the tool shows it beside the estimate. Your own efficiency can differ, so treat the figure as an estimate.

Cyclists training with power meters — a standard tool in platforms like Strava, TrainingPeaks, and Zwift — rely on this power-to-calorie conversion because it stays consistent ride to ride even as fitness improves or heart rate drifts upward from heat or fatigue, unlike calorie estimates based on heart rate zones, which can overstate or understate effort depending on the day.

Was this helpful?

You can pick up to 3 reactions.

Comments

  • Be the first to comment.

Popular calculators

All Calculators