Aquarium Stocking Density Calculator

Enter your tank size and stocking rule to estimate fish capacity.

Result

20.0 in
6.0 in
70.00%

How it is calculated

The tool multiplies tank volume by the stocking rule: capacity = volume × rule. On US units the volume is in US gallons, fish are measured in inches of adult body length and the rule is inches of fish per gallon, so the classic one inch per gallon is entered as 1. With the unit system set to metric the volume is in liters, the fish in centimeters and the rule in centimeters of fish per liter: the classic rule is 2.54 ÷ 3.785411784 = 0.671 cm per liter (the metric default, which gives the same verdict as 1 inch per gallon), and the simpler rule many European keepers use is 1 cm per liter. Remaining space is capacity − current length, and the share used is current / capacity × 100. The current length field may be left empty, which counts as 0. The volume and the rule must be above zero and the current length cannot be negative; otherwise there is no result. Nothing stops the remaining space from turning negative: a minus sign means the tank holds more fish than the rule allows. The rule ignores body shape, waste output, filtration and swimming space, so treat the result as a rough first check.

Worked example

A 20-gallon tank is stocked with fish totaling 14 inches of adult length, using the classic rule of 1 inch per gallon. Capacity = 20 × 1 = 20.0 in. Remaining = 20 − 14 = 6.0 in. The share used is 14 / 20 × 100 = 70.00%. You could therefore add about 6 inches of adult fish, for example two 3-inch tetras, before reaching the limit. If you choose the more cautious rule of 0.5 inch per gallon, capacity falls to 10 in and the same 14 inches would be overstocked.

Try this example →

Common mistakes

  • Entering the rule upside down. A rule of one inch per two gallons is entered as 0.5, not 2; entering 2 doubles the capacity to 40.0 in and gives an overstocked tank a false all-clear.
  • Counting the size fish are in the shop instead of adult length. The rule uses the full-grown size, so a 1-inch juvenile that reaches 6 inches counts as 6.
  • Typing liters and centimeters while the unit system is on US units. A 75-liter tank is about 20 gallons, not 75; switch the unit system to metric instead. On metric the rule is in cm per liter: type 0.671 for the classic inch-per-gallon rule or 1 for the 1 cm per liter rule, not 1 meaning one inch per gallon.
  • Ignoring a negative remaining value. A result such as −6.0 in means 6 inches more fish than the rule allows, and the used share goes above 100% (130.00% for 26 inches in this 20-gallon tank).
  • Using the rule for deep-bodied or messy fish. Goldfish or large cichlids produce far more waste per inch than slim fish, so the same inches need a much larger tank than the simple rule says.

Sources

  • Home Aquariums — Connecticut Department of Energy and Environmental Protection

About this calculator

The inch-per-gallon rule is a rough aquarium stocking guideline: 1 inch of adult fish length per gallon of water for smaller freshwater tanks (sometimes 1 inch per 2 gallons for larger or more waste-heavy species). This calculator multiplies your tank's gallon capacity by the rule ratio to estimate total stockable “fish-inches,” then subtracts what you've already added to show remaining capacity. With the unit system set to metric you enter liters, centimeters and the rule in centimeters of fish per liter: the classic 1 inch per gallon is 0.671 cm per liter (the metric default), and many European keepers use a simpler 1 cm per liter.

The rule is intentionally conservative and ignores body mass, bioload, and swimming behavior — a deep-bodied goldfish or an active schooling fish needs far more space than a slim inch-for-inch comparison suggests, so most experienced keepers treat it only as a starting sanity check. Beginner aquarists and pet-store staff use it to avoid the most common overstocking mistakes before doing species-specific research or testing water parameters after adding new fish.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

Enter the real water volume, not the number on the tank's label. Gravel, rock and decorations take up space, so a tank sold as 55 gallons may hold noticeably less water. The tool then multiplies by your chosen rule, so with the default 55 and 1 inch per gallon the capacity is 55 inches, and 25 remain after 30 inches. Which fish do you keep, and what inches-per-gallon figure has worked for you?

Comments

  • Be the first to comment.

Popular calculators

All Calculators