ADC SNR Calculator

Enter the nominal resolution N, and optionally a measured SINAD, to get the ideal SNR and the effective number of bits.

Result

74.00 dB
10.50
1.50

How it is calculated

The tool evaluates ideal SNR (dB) = 6.02 × N + 1.76, where N is the converter's nominal resolution in bits (more than 0, up to 64). The 6.02 is the dB gain per bit (20·log₁₀2) and 1.76 dB comes from assuming a full-scale sine input and quantization noise only, so the result is the best case for that many bits, rounded to 2 decimals. If you also enter a measured SINAD (signal to noise and distortion, in dB, above 0), it solves the same relation for the bits: ENOB = (SINAD − 1.76) ÷ 6.02, the effective number of bits, and shows N − ENOB, the bits lost to noise and distortion. Leave SINAD empty for the ideal SNR alone. A delta-sigma converter with oversampling can show an ENOB above its output word length, which gives a negative loss.

Worked example

A datasheet gives a nominal 12-bit ADC a SINAD of 65 dB. Ideal SNR from the nominal bits: 6.02 × 12 + 1.76 = 74.00 dB. Effective bits from the measured SINAD: (65 − 1.76) ÷ 6.02 = 10.50. The converter therefore loses 12 − 10.50 = 1.50 bits to noise and distortion, about 9 dB below its ideal SNR.

Try this example →

Common mistakes

  • Typing the ENOB in the N field. The ideal SNR belongs to the nominal bit count; 6.02 × ENOB + 1.76 is the SINAD of a converter with that ENOB, not an ideal SNR.
  • Treating the ideal SNR as what the part will deliver. It counts quantization noise only; thermal noise, jitter and distortion make the measured SINAD lower, and the ENOB line shows by how much.
  • Entering the SNR from the datasheet in the SINAD field. SNR leaves out the harmonics that SINAD includes, so an ENOB worked out from SNR comes out too high.
  • Using a SINAD measured with a signal well below full scale. The 1.76 dB constant assumes a full-scale sine, so a smaller signal understates the ENOB.

Sources

About this calculator

The ideal signal-to-noise ratio of an analog-to-digital converter is set by its nominal resolution N alone, through the classic formula SNR = 6.02 × N + 1.76 dB. The 6.02 dB per bit (20·log₁₀2) comes from each extra bit halving the quantization step, and the 1.76 dB constant from a full-scale sine-wave input with uniformly distributed quantization error and no other noise.

A real converter adds thermal noise, clock jitter and distortion, which a datasheet reports together as SINAD (signal to noise and distortion). Solving the same formula for the bits turns a measured SINAD into the effective number of bits: ENOB = (SINAD − 1.76) / 6.02, so 6.02 × ENOB + 1.76 is the converter's SINAD, not an ideal SNR. Electronics and DSP engineers use the pair to see how many of a part's nominal bits survive: a 12-bit ADC with a SINAD of 65 dB has an ENOB of 10.50, 1.50 bits below its ideal 74.00 dB.

Was this helpful?

You can pick up to 3 reactions.

Note from the editors

Oversampling is one practical use of this number. If quantization noise dominates and the noise is spread evenly across the band, sampling four times faster and averaging down buys about one extra effective bit. A 12-bit converter treated as 13 bits moves from 74.00 dB to 80.02 dB here. Real parts also have thermal noise and jitter, so measure before counting on the gain. What sampling rate and signal bandwidth are you designing around?

Comments

  • Be the first to comment.

Popular calculators

All Calculators